BEHRINGER X1204USB DRIVER MAC OS
BEHRINGER X1204USB DRIVER DRIVER
BEHRINGER X1204USB DRIVER MANUAL
BEHRINGER X1204USB DRIVER DOWNLOAD
BEHRINGER X1204USB DRIVER WINDOWS

LINE 8 ¼” jack will accept either a TRS balanced or TS unbalanced connector for the Right side of a stereo pair of inputs. If the LINE 8 jack isn’t used, the LINE 7 automatically serves as a ‘mono’ signal. LINE 7 ¼” jack will accept either a TRS balanced or TS unbalanced connector for the Left side of a stereo pair of inputs. (These input channels function the same as channels 1-6, except where noted below) MAIN button is used to route the signal from the channel to the MAIN MIX buss SUB button is used to route the signal from the channel to the 1-2 SUB pair SOLO button used in conjunction with the MODE button in the MAIN section to select access of the SOLO or PFL functions. MUTE button allows you to silence the signal in the channelĬHANNEL FADER used for adjustment of the channel output level PAN knob used to define where the signal is placed in the stereo ‘field’ MON knob controls the level sent from the channel to the MON busĪUX 2/FX knob controls the level sent from the channel to the internal FX bus, or it can be sent to a ‘post’ fader AUX send bus GAIN knob controls the input level for MIC and LINE inputsĮQ HI knob used to boost or cut the high frequency rangeĮQ MID knob used to boost or cut the middle frequency rangeĮQ FREQ knob use to select the center frequency to be controlled by the EQ MID knobĮQ LO knob used to boost or cut the low frequency range LO CUT button when this is pressed in, it engages a filter that cuts the low frequency range at 75 Hz and below, to remove stage ‘rumble’ and similar sounds. A special insert Y-cable is used, with a ¼” Tip/Ring/Sleeve on one end, and two ‘mono’ 2-conductor (Tip/Sleeve) connectors on the other end. INSERT jack a ¼” TRS 3-conductor jack (located on the back of the mixer) that acts as both a send and return to be used with a processor, like a compressor or effect unit. LINE IN input ¼” balanced (TRS) or unbalanced (2 -conductor) signal MIC input XLR balanced connection for a mic or similar low impedance signal (Note: Many of these controls are covered in greater detail (with examples) in the application guides that follow) Starting from the top of the channel ‘strip’ for channels 1 through 6: Make sure there are no SOLO buttons pressed on any of the channels. Make sure channel 1 MUTE button is not pressed. If you have a microphone connected to channel 1, make sure the MAIN button is pressed on channel 1 in order to assign that channel to the main mix. Remember any of the input channels routed to the main mix, should also be sent to the USB output as well. Software play through (play new track while recording it) Play other tracks while recording new ones. In the recording section, you will want to have the channels selection set to 2(stereo)<<<<<<<<<< This is where you select the USB interface. In the Audio I/O menu, here you can select the playback device and recording device. Go into the edit > preferences menu of Audacity.

BEHRINGER X1204USB DRIVER DOWNLOAD

You can download Audacity from the BEHRINGER website.Īlternately, you can get Audacity directly from Sound Force.

BEHRINGER X1204USB DRIVER MANUAL

Refer to the users manual of your recording software for more information. There should be some kind of preferences menu or options menu to select it. In addition you will need to select what interface is assigned in your recording software. Also set the recording to USB Audio Codec.

BEHRINGER X1204USB DRIVER WINDOWS

Also set the default recording to USB Audio Codec.įrom the Start menu in Windows Vista, go to control panel > sounds. Set your default sound playback to USB Audio Codec.

BEHRINGER X1204USB DRIVER DRIVER

The interface built into the mixer doesn't have to have a driver of it's own at all.įrom the Start menu in Windows XP, go to control panel > sounds & audio devices > select audio. The interface built into the mixer uses the generic Microsoft USB driver, which is built in to Windows XP.

BEHRINGER X1204USB DRIVER MAC OS

This means that it doesn't need a driver to be installed when used with Windows XP or Mac OS X. The USB interface built into the mixer is class compliant under Windows and uses core audio driver on a Mac.

You will be able to monitor through the speakers or the headphones. You will want to connect the control room outputs to your power amp or powered speakers and control your monitoring level via the CTRL ROOM knob.

You will need to select the 2TR/USB to CTRL ROOM button so that the computer output will be routed away from the main mix to the CTRL ROOM output. If you toggle the red 2-tr/usb buttons, then it will fix the issue.Ĭonnect the USB connection from the mixer to your computer. Information that I received from Behringer.

Behringer x1204usb driver